Logo

MonoCalc

/

Eyring Equation Calculator

Chemistry
0 < κ ≤ 1; usually 1
1 M standard state: only the unit label changes.

Rate constant k

5.9961 × 10⁻² s⁻¹

ln k = -2.8141 (k in s⁻¹)

Frequency factor k_B·T/h

6.2124 × 10¹² s⁻¹

upper limit of k at this temperature

ΔG‡ in other units

19.120 kcal/mol

Half-life t½

11.6 s

t½ = ln 2 / k

Equivalent Arrhenius Eₐ

82.479 kJ/mol

Eₐ = ΔH‡ + RT

Equivalent pre-exponential A

1.6887 × 10¹³ s⁻¹

A = κ·(e·k_B·T/h)·exp(ΔS‡/R)

Arrhenius conversion assumes a reaction in solution or a unimolecular gas-phase reaction. Bimolecular gas-phase reactions use Eₐ = ΔH‡ + 2RT and a pressure standard state, which is out of scope. A 1 M standard state is assumed throughout.

Reaction coordinateFree energy GΔG‡ = 80.000 kJ/mol‡ReactantsProducts (schematic)

Half-life timescale (first-order)

Log scale from 1 ns to 1000 years. The lower row gives the ΔG‡ (kJ/mol) that produces each half-life at 298.15 K.

ns22.6µs39.7ms56.8s73.9min84.1h94.2day102.1year116.7century128.2t½ΔG‡t½ = 11.6 s

log₁₀ k vs temperature (T ± 50 K)

Solid: Eyring equation. Dashed: Arrhenius approximation with Eₐ and A taken at 298.15 K. ΔG‡ is treated as temperature-independent (ΔH‡ = ΔG‡, ΔS‡ = 0). k in s⁻¹. Largest gap between the two curves over this range: 1.81% in k.

Calculation steps

1. T = 298.15 K, κ = 1

2. k_B·T/h = (1.380649 × 10⁻²³ × 298.15) / 6.62607015 × 10⁻³⁴ = 6.2124 × 10¹² s⁻¹

3. ΔG‡/(R·T) = 80000.0 / (8.314462618 × 298.15) = 32.27164

4. k = κ·(k_B·T/h)·exp(−ΔG‡/RT) = 5.9961 × 10⁻² s⁻¹

Constants (exact SI): k_B = 1.380649 × 10⁻²³ J/K, h = 6.62607015 × 10⁻³⁴ J·s, R = 8.314462618 J/(mol·K); 1 cal = 4.184 J. A 1 M standard state is assumed; gas-phase pressure standard states are out of scope.

About This Tool

Eyring Equation Calculator – Rate Constants from Transition-State Theory

The Eyring equation, also called the Eyring–Polanyi equation, connects the speed of a chemical reaction to the thermodynamics of its transition state. This Eyring equation calculator works in four directions. It turns a free energy of activation into a rate constant and a half-life, recovers ΔG‡ from a measured rate constant, finds the temperature that gives a target rate, and fits an Eyring plot to your own kinetic data to extract ΔH‡ and ΔS‡ with standard errors.

Transition-state theory in plain words

On the way from reactants to products, molecules pass through a highest-energy arrangement called the activated complex, marked with the double dagger ‡. Transition-state theory assumes this complex is in a quasi-equilibrium with the reactants. It also assumes that complexes cross over into products at a universal frequency, k_B·T/h, which is about 6.21 × 10¹² s⁻¹ at 25 °C. The rate constant is that frequency multiplied by the fraction of molecules that reach the top of the barrier:

k = κ · (k_B·T / h) · exp(−ΔG‡ / RT) = κ · (k_B·T / h) · exp(ΔS‡ / R) · exp(−ΔH‡ / RT) ΔG‡ = ΔH‡ − T·ΔS‡

The calculator uses the exact SI 2019 constants. A useful rule of thumb follows from them. At room temperature, every 5.7 kJ/mol (1.36 kcal/mol) added to the barrier slows a reaction tenfold. A barrier of 80 kJ/mol gives a first-order half-life of about 12 seconds, and one of 100 kJ/mol takes about 10 hours. The timescale ruler under each result shows this link between barrier height and half-life.

What the transmission coefficient κ means

Not every molecule that reaches the transition state goes on to products. Some recross the barrier and fall back to reactants. The transmission coefficient κ is the fraction that does go on. Simple transition-state theory sets κ = 1, and the measured activation parameters absorb any small correction, so that is the usual default. Lower values are used for nonadiabatic electron transfers, for reactions in very viscous solvents, or when you compare against detailed dynamics calculations. Proton and hydrogen transfers can tunnel through the barrier. That effect is sometimes written as κ > 1, but it is outside the simple theory, so this tool only accepts 0 < κ ≤ 1.

Eyring vs Arrhenius

The Arrhenius equation, k = A·exp(−Eₐ/RT), is empirical. It describes how rates change with temperature without saying what A means. The Eyring equation gives the same temperature dependence a physical meaning. Its parameters are an enthalpy and an entropy that you can compare with the Gibbs free energy of the overall reaction. For reactions in solution the two descriptions convert directly, using Eₐ = ΔH‡ + RT and A = (e·k_B·T/h)·exp(ΔS‡/R). The k vs T chart overlays both curves. They agree near the chosen temperature and drift apart away from it, because Eₐ itself depends slightly on temperature. Arrhenius parameters are the usual choice for engineering rate laws and shelf-life work. Eyring parameters are preferred when you want to reason about mechanism.

How to read an Eyring plot

Taking logarithms gives a straight line, ln(k/T) = −(ΔH‡/R)·(1/T) + ln(κ·k_B/h) + ΔS‡/R. Plot ln(k/T) against 1/T. The slope gives the enthalpy of activation, and the intercept, after subtracting ln(k_B/h) ≈ 23.760, gives the entropy of activation. Measure rates over as wide a temperature range as you can. The intercept is a long extrapolation to 1/T = 0, so ΔS‡ always carries a larger uncertainty than ΔH‡. Their errors are correlated, which is why ΔG‡ near the middle of your data is determined much more precisely than either one. Curvature or a low R² can point to a change of mechanism or a rate-limiting step that shifts with temperature.

Units matter for ΔS‡
The intercept, and so ΔS‡, depends on the units of k. Enter rate constants in s⁻¹, or pick the matching time unit so the calculator can convert them. Bimolecular rate constants are interpreted with a 1 M standard state.

What a negative ΔS‡ tells you

A negative entropy of activation means the transition state is more ordered than the reactants. This is typical of associative mechanisms, where two molecules combine into one complex. Examples include SN2 substitutions, Diels–Alder cycloadditions and ligand association at metal centres, which often show ΔS‡ between −50 and −150 J/(mol·K). Strongly solvated, charge-separated transition states give negative values too. A positive ΔS‡ points to a looser transition state, such as a bond breaking in a dissociative or unimolecular step. In the stacked bar beside the energy diagram, a negative ΔS‡ appears as a positive −TΔS‡ term that raises the barrier above ΔH‡.

For related equilibrium questions, see the Van 't Hoff equation calculator. To turn a rate constant into concentrations over time, use the reaction rate law calculator.

Frequently Asked Questions

Is the Eyring Equation Calculator free?

Yes, Eyring Equation Calculator is totally free :)

Can I use the Eyring Equation Calculator offline?

Yes, you can install the webapp as PWA.

Is it safe to use Eyring Equation Calculator?

Yes, any data related to Eyring Equation Calculator only stored in your browser (if storage required). You can simply clear browser cache to clear all the stored data. We do not store any data on server.

How does this Eyring equation calculator work?

It applies the Eyring–Polanyi equation k = κ·(k_B·T/h)·exp(−ΔG‡/RT) with the exact SI values of k_B, h and R. You can get k from activation parameters, ΔG‡ from a measured k, the temperature that gives a target rate, or ΔH‡ and ΔS‡ from a least-squares fit of ln(k/T) against 1/T.

What is k_B·T/h in the Eyring equation?

It is the universal frequency factor: the rate at which a transition state crosses into products, about 6.21 × 10¹² s⁻¹ at 25 °C. It is the largest rate constant transition-state theory allows, reached only for a reaction with no free-energy barrier.

What ΔG‡ corresponds to a reaction that is fast at room temperature?

At 25 °C a first-order reaction with ΔG‡ = 80 kJ/mol (19.1 kcal/mol) has a half-life of about 12 seconds, and each extra 5.7 kJ/mol slows it roughly tenfold. Barriers near 100 kJ/mol give half-lives of hours to days, which is why many reactions need heating.

How do I convert Eyring parameters to Arrhenius Eₐ and A?

For reactions in solution and unimolecular gas-phase reactions, Eₐ = ΔH‡ + RT and A = (e·k_B·T/h)·exp(ΔS‡/R). Bimolecular gas-phase reactions use Eₐ = ΔH‡ + 2RT and a pressure standard state, which this calculator does not handle.

Why are the errors in ΔH‡ and ΔS‡ so large but ΔG‡ precise?

ΔS‡ comes from extrapolating the Eyring plot to 1/T = 0, far outside the measured range, so any error in the slope moves the intercept the opposite way. The two errors cancel in ΔG‡ near the mean temperature of the data, a statistical form of enthalpy–entropy compensation.

What does the transmission coefficient κ mean?

κ is the fraction of trajectories that reach the transition state and go on to products instead of recrossing back. It is usually set to 1, the transition-state theory assumption; values below 1 account for recrossing or nonadiabatic effects and lower the predicted rate.