Logo

MonoCalc

/

Kjeldahl Nitrogen Calculator

Chemistry
A reagent blank is strongly recommended.
Used: 0.1000 N HCl = 0.1000 N
Adds a dry-basis result.

Replicates (optional)

1. Digest

Organic N → (NH₄)₂SO₄

Hot H₂SO₄ with catalyst

2. Distil

NH₄⁺ + OH⁻ → NH₃↑

into boric acid

3. Titrate

net 21.20 mLblank 0.15 mL

21.20 mL × 0.1000 N = 2.120 mmol NH₃

4. Nitrogen

2.120 mmol × 14.0067 = 29.69 mg N in 0.5012 g

→ 5.925 % N

5. Protein

5.925 % × 6.25 = 37.03 % protein

Results

Nitrogen

5.925 %

Protein (as is)

37.03 %

mg N

29.694

mmol NH₃

2.1200

About This Tool

Kjeldahl Nitrogen Calculator – From Titration to % Nitrogen and % Protein

The Kjeldahl method is the reference technique for total organic nitrogen and, from it, crude protein in food, feed, soil, fertiliser and wastewater laboratories. This Kjeldahl nitrogen calculator turns your sample mass, burette readings and titrant concentration into %N and % protein, and shows every step so you can compare the result with your lab notebook.

How the Kjeldahl method works

A weighed sample is digested in hot sulfuric acid with a catalyst, converting organic nitrogen into ammonium sulfate. The digest is made alkaline with NaOH and the liberated ammonia is distilled into a receiving solution. The ammonia is then measured by titration in one of two ways.

  • Boric acid (direct) titration: NH₃ is trapped in boric acid and titrated directly with standard acid.
  • Back titration: NH₃ is trapped in a known excess of standard acid and the unreacted acid is titrated with standard NaOH.

Formulas used

With volumes in mL and mass in g, mmol × 14.0067 gives mg of nitrogen:

%N = (V_s − V_b) × N_acid × 1.40067 / W for the direct method.

mmol NH₃ = V_acid × N_acid − V_NaOH × N_NaOH for a back titration without a blank, or (V_blank − V_sample) × N_NaOH when a blank is run.

% protein = %N × F, and the dry-basis value divides by (1 − moisture / 100).

Molarity versus normality
Sulfuric acid is diprotic, so 0.0500 mol/L H₂SO₄ is 0.1000 N. The calculator always shows the normality it actually used, so the factor of two is never hidden.

Why the protein factor matters

Kjeldahl measures nitrogen, not protein. Protein is estimated by multiplying %N by a factor that assumes a typical nitrogen content of the protein. The traditional 6.25 assumes 16 % nitrogen, but real proteins differ. Jones factors, as tabulated by FAO, use 6.38 for dairy, 5.70 for refined wheat flour, 5.71 for soybeans and 5.18 for almonds. Mariotti et al. (2008) argue that 6.25 overestimates protein in most foods and suggest 5.6 as a general value. Always state the factor you used when reporting protein.

Blanks, replicates and sanity checks

A reagent blank corrects for nitrogen in the reagents and for titrant used to reach the endpoint. Running replicates lets you see the mean, standard deviation and relative standard deviation; an RSD above about 2 % suggests poor agreement. In a back titration, if the ammonia consumes more than about 90 % of the acid in the receiver, some ammonia may have escaped, so repeat with more acid or less sample.

Limitations

Standard Kjeldahl does not recover nitrate or nitrite nitrogen; modified procedures such as Devarda or salicylic acid digestion are needed. Non-protein nitrogen, such as melamine, inflates apparent protein. Combustion (Dumas) analysis is an alternative technique with its own conversion factors. This tool covers only the arithmetic after titration.

Frequently Asked Questions

Is the Kjeldahl Nitrogen Calculator free?

Yes, Kjeldahl Nitrogen Calculator is totally free :)

Can I use the Kjeldahl Nitrogen Calculator offline?

Yes, you can install the webapp as PWA.

Is it safe to use Kjeldahl Nitrogen Calculator?

Yes, any data related to Kjeldahl Nitrogen Calculator only stored in your browser (if storage required). You can simply clear browser cache to clear all the stored data. We do not store any data on server.

How does the Kjeldahl nitrogen calculator work?

It converts the net titrant volume and acid concentration into mmol of NH3, multiplies by 14.0067 to get mg of nitrogen, and divides by the sample mass to give %N. Multiplying %N by a protein factor gives crude protein.

Which protein factor should I use?

6.25 is the general default, but foods differ: 6.38 for dairy, 5.70 for refined wheat flour, 5.71 for soybeans. Use the factor required by your method or regulation and always report it with the result.

Why does H2SO4 concentration get doubled?

Sulfuric acid supplies two protons per molecule, so a concentration in mol/L is twice as many equivalents per litre. 0.0500 M H2SO4 equals 0.1000 N, and the calculator shows this conversion.

When do I use the back-titration mode?

Use it when ammonia is distilled into a known excess of standard acid rather than boric acid. The unreacted acid is titrated with standard NaOH, and the NH3 is found by difference.

Does Kjeldahl measure nitrate nitrogen?

No. The standard method recovers organic and ammonium nitrogen but not nitrate or nitrite, which need modified procedures. Non-protein nitrogen such as melamine is counted and can inflate apparent protein.