Logo

MonoCalc

/

Mean Free Path Calculator

Chemistry

Method

Solve for

Quick conditions

Diameter source: viscosity-derived hard-sphere values. Other sources (Lennard-Jones σ, kinetic diameter) differ by up to ~25 %; enter your own value if your textbook uses a different one.
Needed only for the mean speed, collision frequency and time between collisions.
Scientific notation works: 1e-6 or 1×10⁻⁶.
Gives the Knudsen number Kn = λ / L and the flow regime.

Mean free path λ

65.43 nm

6.543 × 10⁻⁸ m

Pressure P

Atmospheric

1 atm

Number density n

n = P / (k_B T)

2.446 × 10²⁵ m⁻³
2.446 × 10¹⁹ cm⁻³

Collision diameter d

0.375 nm

Collision cross-section σ

σ = πd²

4.418 × 10⁻¹⁹ m²
0.4418 nm² · 44.18 Ų

Mean speed v̄

√(8RT / πM)

476.2 m/s

Collision frequency z

Per molecule, z = v̄ / λ

7.278 × 10⁹ s⁻¹

Mean time between collisions τ

τ = 1 / z

137.4 ps

Mean intermolecular spacing

n^(−1/3)

3.445 nm

λ / d

Molecular diameters travelled between hits

174.5

Mean free path vs pressure

Compare gases (up to 4, hard-sphere at the same temperature)

Nitrogen (N₂)

λ falls as 1/P, so each gas is a straight line of slope −1 on log–log axes. The dot marks your conditions (1 atm, λ = 65.4 nm). Shaded bands are the conventional vacuum ranges; boundaries differ slightly between ISO and AVS schemes.

How long is that? Length-scale ruler

100 pm1 nm1 µm1 mmAtomVirusVisible lightBacteriumHuman hair1 cm1 mRoom1 kmd = 375 pmspacing 3.44 nmλ = 65.4 nm

The collision cylinder

λ ≈ 65.4 nmCylinder radius d = 375 pm; cross-section σ = πd² = 0.442 nm²Any molecule whose centre lies inside the shaded cylinder is hit.Schematic, not to scale.

About This Tool

Mean Free Path Calculator – How Far Gas Molecules Travel Between Collisions

The mean free path (λ) is the average distance a gas molecule flies in a straight line before it hits another molecule. It decides whether a gas behaves like a continuous fluid or like a spray of independent particles, which is why it matters in vacuum engineering (sputtering, evaporation, mass spectrometers, electron microscopes), aerosol science, microfluidics and every physical-chemistry course on kinetic theory. This calculator gives λ from temperature, pressure and molecular diameter, solves the same equation for the pressure, temperature or diameter instead, and reports the Knudsen number for a length you choose.

The mean free path formula

Picture one molecule of diameter d moving through the gas. It hits any molecule whose centre comes within d of its path, so as it moves it sweeps out a collision cylinder of cross-section σ = πd². With n = P / (k_B·T) molecules per cubic metre, the average distance between hits is:

λ = 1 / (√2 · n · σ) = k_B·T / (√2 · π · d² · P)

Here k_B = 1.380649 × 10⁻²³ J/K is the Boltzmann constant. The mean free path rises in proportion to temperature and falls in inverse proportion to pressure, so on a log–log plot of λ against P every gas is a straight line of slope −1. Molar mass does not appear at all: a heavy molecule moves more slowly, but it also meets its neighbours more slowly, and the two effects cancel.

Where the √2 comes from

Clausius's original derivation assumed the other molecules stand still, which gives λ = 1/(nσ). In a real gas all molecules move, and the quantity that sets the collision rate is the mean relative speed between two molecules. For a Maxwell–Boltzmann distribution this is v̄_rel = √2 · v̄, so collisions happen √2 times as often and λ is √2 times shorter. The older form without √2 overestimates the mean free path by about 41 %.

Related quantities in the results

  • Collision frequency z = v̄ / λ, with the mean speed v̄ = √(8RT/πM). This is where the molar mass is needed.
  • Mean time between collisions τ = 1/z: about 140 ps for nitrogen at room conditions.
  • Mean intermolecular spacing n^(−1/3): about 3.4 nm at 1 atm, so a molecule passes many neighbours for every one it hits.
  • λ/d: how many of its own diameters a molecule travels between collisions.

Worked example: nitrogen at room conditions

For N₂ at 300 K and 1 atm with d = 0.375 nm: n = 101325 / (1.380649 × 10⁻²³ × 300) = 2.446 × 10²⁵ m⁻³, σ = π × (0.375 nm)² = 0.4418 nm², and λ = 1 / (√2 × 2.446 × 10²⁵ × 4.418 × 10⁻¹⁹) = 65.4 nm. At a mean speed of 476 m/s each molecule collides about 7.3 × 10⁹ times per second. Pump the same gas down to high vacuum at 10⁻⁶ Torr and λ grows to tens of metres, longer than any chamber, so molecules travel from source to wall without meeting each other. To find the pressure that gives a chosen λ, switch "Solve for" to P.

Getting λ from viscosity instead

Gas viscosity is caused by molecules carrying momentum across a distance of about one mean free path, so a measured viscosity μ gives λ without choosing a diameter: λ = (μ/P) · √(π·k_B·T / 2m), where m = M/N_A is the mass of one molecule. This route is common in aerosol science. For air, the calculator can fill in μ from Sutherland's law. At 20 °C and 1 atm both methods give about 65 nm.

Which molecular diameter?
Hard-sphere diameters from viscosity data, Lennard-Jones σ values and zeolite "kinetic diameters" are three different quantities and can differ by 25 %. The presets use viscosity-derived values. If your course uses another table, type its value in. Air is treated as a single effective gas.

Knudsen number and flow regimes

Whether λ is "long" depends on the size of the system. The Knudsen number Kn = λ / L compares it with a characteristic length L such as a pipe diameter, MEMS channel, pore or particle size. Below Kn ≈ 0.01 the gas is a continuum and the Navier–Stokes equations apply. From 0.01 to 0.1 is slip flow, from 0.1 to 10 is transition flow, and above 10 the flow is free molecular, with molecules hitting walls far more often than each other. Vacuum technology often puts the start of molecular flow at Kn ≈ 1 instead.

Limits of the model
The formula assumes a dilute ideal gas of hard spheres. It becomes unreliable above roughly 10 MPa, or when λ is only a few molecular diameters, and it does not cover gas mixtures species by species, ions in plasmas, or electrons and photons in solids.

Frequently Asked Questions

Is the Mean Free Path Calculator free?

Yes, Mean Free Path Calculator is totally free :)

Can I use the Mean Free Path Calculator offline?

Yes, you can install the webapp as PWA.

Is it safe to use Mean Free Path Calculator?

Yes, any data related to Mean Free Path Calculator only stored in your browser (if storage required). You can simply clear browser cache to clear all the stored data. We do not store any data on server.

How does this mean free path calculator work?

It converts your inputs to SI units, finds the number density n = P/(k_B·T) and the collision cross-section σ = πd², then applies λ = 1/(√2·n·σ) = k_B·T/(√2·π·d²·P). Because that is a simple product, it can also solve for pressure, temperature or diameter, and the viscosity method uses λ = (μ/P)·√(π·k_B·T/2m) instead.

What is the mean free path of air at room temperature and pressure?

About 65 nm. With an effective diameter of 0.372 nm at 20 °C and 1 atm the hard-sphere formula gives 65.0 nm, and the viscosity route with Sutherland's law for air gives 65.1 nm, so the two methods agree within a fraction of a percent.

What pressure do I need so molecules cross my vacuum chamber without colliding?

Choose Solve for P and enter the chamber size as the target λ. For nitrogen at 300 K, λ = 1 m needs about 6.6 × 10⁻³ Pa (5 × 10⁻⁵ Torr), which is in the high-vacuum range. A handy rule for room-temperature air is λ in cm ≈ 5 × 10⁻³ divided by P in Torr.

Why do different sources give different molecular diameters?

There are several kinds of diameter: hard-sphere values derived from viscosity, the Lennard-Jones σ parameter, and zeolite kinetic diameters. They disagree by up to about 25 %. This tool uses viscosity-derived values by default, but you can type in any diameter your textbook uses.

What is the Knudsen number and which flow regime am I in?

The Knudsen number Kn = λ/L compares the mean free path with a characteristic length such as a channel width. Conventionally Kn < 0.01 is continuum flow, 0.01–0.1 slip flow, 0.1–10 transition flow and above 10 free-molecular flow, though vacuum texts often call Kn > 1 molecular flow.

When is the mean free path formula not accurate?

It assumes a dilute ideal gas of hard spheres. It breaks down at high pressure (above roughly 10 MPa) or when λ is only a few molecular diameters, and it treats air as a single effective gas. For ions in plasmas, electrons in solids or real-gas behaviour you need other models.