Logo

MonoCalc

/

Capacitor Energy Calculator

Physics
Enter any two; the other two are derived.
Stored energy E
103.7 J
103.7 J = 28.8 mWh
Charge Q
14.4 C
4 mAh
Capacitance C
1 F
Voltage V
14.4 V
Equivalent lift
10.57 m
Height this energy could raise a 1 kg mass

Energy vs voltage

081 J162 J9 V18 Vvoltage →stored energy 100 J limit14.4 V, 103.7 J

E = ½CV² is a parabola: halving the voltage leaves only a quarter of the energy.

Worked steps

Charge

Q = C·V = 1 F × 14.4 V = 14.4 C

Energy

E = ½·C·V² = 0.5 × 1 F × (14.4 V)² = 103.7 J

Charge in mAh

Q[mAh] = Q[C] ÷ 3.6 = 4 mAh

Equivalent lift

h = E ÷ (1 kg × 9.80665 m/s²) = 10.57 m

Stored-energy hazard check

Above stored-energy hazard threshold

103.7 J at 14.4 V is 1.04× the 100 J threshold for below 100 V.

VoltageThreshold (stored energy)

below 100 V

this capacitor
100 J

100 V to 400 V

1 J

above 400 V

0.25 J

Approximate, based on summaries of NFPA 70E Article 360 (2021 edition onward). Check the current standard and your site's procedures.

Informational only. Treat any charged capacitor as live; discharge through a suitable resistor and verify with a meter.

About This Tool

Capacitor Energy Calculator – Stored Energy, Usable Energy and Hold-Up Time

A capacitor energy calculator usually answers one question: how many joules sit in a capacitor of capacitance C charged to voltage V. The answer is the textbook formula E = ½·C·V². In practice that number is only half the story. A supercapacitor backing up a microcontroller, a camera-flash capacitor or a car-audio stiffening cap is useful only down to some minimum voltage, and the load decides how quickly it gets there. This tool starts from the capacitor you already have and works through stored energy, usable energy, hold-up time, capacitor sizing, supercapacitor banks and a stored-energy hazard check.

The four linked quantities: E, C, V and Q

Charge, capacitance and voltage are tied together by Q = C·V, and the stored energy can be written three equivalent ways: E = ½·C·V² = ½·Q·V = Q²/(2C). Any two of the four quantities fix the other two, so the stored-energy mode lets you pick which pair you know. A 1 F capacitor at 14.4 V, for example, holds 103.68 J (about 28.8 mWh) and a charge of 14.4 C, which is 4 mAh in battery terms, since 1 mAh = 3.6 C. To give the number a sense of scale, the tool also shows how high that energy could lift a 1 kg mass: just over 10 metres.

Why energy scales with V², and why the last volts are nearly empty

Moving each extra coulomb onto a capacitor takes more work than the last, because the voltage it is pushed against keeps rising. Adding up that work gives the factor of one half and the square of the voltage. The square has a practical consequence. If a circuit runs from a starting voltage V₁ down to a minimum V₂, the energy released is ΔE = ½·C·(V₁² − V₂²), and the usable fraction is 1 − (V₂/V₁)². Dropping from 5 V to 2.5 V releases 75 % of the stored energy, not 50 %. Letting the voltage sag to half its starting value already gives up three quarters of the energy, and the remaining quarter stays stranded in the capacitor.

Hold-up time depends on the load

The same usable energy lasts different lengths of time depending on how the load draws it. The calculator models three common cases:

LoadHold-up timeVoltage shape
Constant power (DC-DC converter)t = η·C·(V₁² − V₂²)/(2P)Square-root collapse
Constant current (linear regulator, LED driver)t = C·(V₁ − V₂)/IStraight line
Resistivet = R·C·ln(V₁/V₂)Exponential tail

A constant-power load draws more current as the voltage falls, so it can never run down to 0 V. The current would become infinite, and the calculator asks for a minimum voltage instead. A resistive load is the opposite: it slows down as the voltage drops and, in theory, never reaches zero at all. Switch the tool to minimum capacitance to run the same formulas backwards. Enter the hold-up time you need and it returns the smallest capacitance that delivers it, the next E6 value up, and a figure with a 20 % margin for parts that are often specified at −20 % tolerance.

ESR shortens real hold-up times
Near the end of a constant-power discharge the current is at its highest, and the capacitor's equivalent series resistance drops a voltage the ideal model ignores. If you enter an ESR, the tool warns when that drop exceeds 10 % of V₂.

Capacitor banks: arrangement trades voltage for capacitance

Supercapacitor cells are rated at only 2.5–3 V, so useful modules wire them in series strings. With N cells in series and M strings in parallel, the bank capacitance is M·C_cell/N and the bank voltage is N·V_cell. The total energy is simply N·M times one cell's energy, however the cells are arranged. Six 3000 F, 2.7 V cells in series make a 500 F, 16.2 V module storing 65.6 kJ (about 18 Wh). Series strings need cell balancing: every cell carries the same charge, so a cell with slightly less capacitance ends up at a higher voltage and can be pushed past its rating.

If you also enter the cell mass, the bank mode reports specific energy in Wh/kg. As a rough order of magnitude, supercapacitors store a few Wh/kg while lithium-ion cells store well over a hundred. Capacitors trade that energy density for very high power, long cycle life and simple charging. Charging a capacitor through a resistor also wastes energy, which the RC time constant calculator covers.

Stored-energy hazard check

Every result is compared with voltage-tiered stored-energy thresholds: 100 J below 100 V, 1 J from 100 V to 400 V, and 0.25 J above 400 V. These figures are approximate, based on secondary summaries of NFPA 70E Article 360 (2021 edition onward) rather than the standard's own text. Older guidance used a single 10 J threshold at 100 V and above. A camera-flash capacitor at 330 V holds about 18 J, many times its threshold, which is why such parts deserve respect long after the device is switched off.

Informational only
Treat any charged capacitor as live; discharge through a suitable resistor and verify with a meter.

Frequently Asked Questions

Is the Capacitor Energy Calculator free?

Yes, Capacitor Energy Calculator is totally free :)

Can I use the Capacitor Energy Calculator offline?

Yes, you can install the webapp as PWA.

Is it safe to use Capacitor Energy Calculator?

Yes, any data related to Capacitor Energy Calculator only stored in your browser (if storage required). You can simply clear browser cache to clear all the stored data. We do not store any data on server.

How does this capacitor energy calculator work?

Pick any two of capacitance, voltage, charge and energy and the calculator derives the other two from Q = C·V and E = ½·C·V². The usable-energy mode then works out how much of that energy a load can draw before the voltage falls to a minimum, and how long that takes for a constant-power, constant-current or resistive load.

Why can't I use all the energy stored in a capacitor?

Because energy rises with the square of voltage, the last volts hold very little of it, and most circuits stop working well before the capacitor is empty. Only ½·C·(V₁² − V₂²) is released between a starting voltage V₁ and a minimum V₂, which is a fraction 1 − (V₂/V₁)² of the total.

Does wiring cells in series or parallel change the total energy?

No. A bank of identical cells stores N·M times the energy of one cell however they are arranged. Series wiring raises the voltage and lowers the capacitance, parallel wiring does the opposite, and the product ½·C·V² stays the same.

How do I size a capacitor for a required hold-up time?

Switch the usable-energy mode to solve for capacitance, enter the hold-up time, the voltage window and the load. The calculator returns the minimum capacitance, the next larger E6 value, and a value with a 20 % margin so a part at the low end of a −20 % tolerance still meets the requirement.

How accurate are the hold-up times?

They are ideal results: capacitance is taken as constant, leakage is ignored, and the capacitor's ESR is left out of the discharge model. Real hold-up is shorter when ESR drops a noticeable voltage at the end of discharge, which the calculator flags, and when the capacitor is below its nominal value.

Are the hazard thresholds official?

They are approximate figures based on summaries of NFPA 70E Article 360, which sets stored-energy thresholds that fall as voltage rises. Treat the check as informational only and follow the current standard and your own safety procedures.